Digital Security Controls PC1575 Especificaciones descargar pdf (Pagina 19)

P R O G R A M D E S C R I P T I O N S

When power is applied to the panel, downloading

will be enabled for six hours. This will allow you to

perform downloading without having to do any

keypad programming.

If the Downloading Answer option is enabled, or during the

first six hours after power up, the panel will answer calls for

downloading when the programmed Number of Rings is

heard by the panel.

If the Answering Machine Override option is enabled (or

during the first six hours after power up), the panel will

answer incoming calls for downloading in the following

manner:

1. The panel hears one or two rings then misses a ring.

2. At this point the panel will start a timer.

3. If the panel hears another ring before the

Answering Machine Double-Call Timer expires, it

will answer on the first ring of the second call.

The panel will immediately go on line and begin downloading.

If the Call-Back option is enabled, the panel and the computer

will both hang up. The panel will then call the Downloading

Computer’s Telephone Number and wait for the computer

to answer. Once the computer answers, downloading will

begin.

If the User Enabled DLS Window for One Hour option is

ON, the user can activate the downloading feature for one

hour by entering [

✱] [6] [Master Code] [5]. After one hour,

the panel will not answer incoming calls unless the

Downloading Answer option is enabled.

The Download Access Code and Panel Identifier Code are

for security and proper identification. Both the panel and the

computer file should contain the same information programmed

before attempting to download.

The time to complete a successful download can be

significantly reduced with the use of the PC-LINK. This

adaptor will allow on-site downloading of supported panels to

occur. To Initiate Local Downloading via the PC-LINK,

enter [

✱] [8] [Installer’s Code] [77] [Installer’s Code] [77].

Downloading can also be performed through the LINKS 1000

cellular communicator if the phone line is disconnected. If

Call Back is being used, you may have to program the LINKS

1000 Preamble to have the panel call the computer correctly.

When a Zone Status Upload is performed through

PC-Link, the information uploaded may not be

accurate. For more information refer to the Download

Manual included with the computer software.

Downloading Answer ..................... Section [71], Option [1]

Number of Rings ................................................Section [70

]

Answering Machine Override........ Section [71], Option [6]

User Enable DLS Window for One Hour ........ Section [71],

Option [2]

Call-Back ........................................ Section [71], Option [3]

Answering Machine Double Call Timer .......... Section [75]

Download Computer Telephone Number....... Section [72]

Download Access Code .................................. Section [73]

Panel Identification Code ................................ Section [74]

Initiate Local Downloading (PC-LINK) ............ Section [77]

LINKS 1000 Preamble (Downloading) ............. Section [79]

5.10 Telephone Line Monitor (TLM)

The panel will supervise the presence of the phone line and

will indicate a trouble condition if the phone line is

disconnected. If the TLM Enabled option is selected, the

panel will wait for the TLM Trouble Delay time period before

indicating the trouble so that a momentary interruption of the

phone line will not cause a trouble condition.

If the TLM Trouble Only option is enabled, the panel will

indicate a TLM trouble only at the keypad if the system is

armed. To activate the bell output in the case of a TLM

trouble while the system is armed, the Audible When

Armed option must be selected.

When the trouble condition is restored, the panel can send

a TLM Restoral Reporting Code. Any events which occur

while the phone line is down will also be communicated.

If the LINKS 1000 Cellular Communicator is being used, the

panel can be programmed to report a TLM Trouble

Reporting Code.

TLM Enable/Disable

.......................

Section [08], Option [5]

TLM Trouble Only or

Audible When Armed .................... Section [08], Option [6]

TLM Trouble Reporting Code

..........................

Section [43]

TLM Restoral Reporting Code

.........................

Section [44]

TLM Trouble Delay

..........................

Section [62], Option [1]

5.11 Siren Supervision

The panel supervises the Bell output. If an open condition is

detected or if the fuse is blown, the panel will immediately

indicate a trouble condition by beeping the keypad twice

every 10 seconds to alert the owner of the problem. The

panel can send a Bell Circuit Trouble Reporting Code

immediately. Once the problem is corrected, the panel can

send a Bell Circuit Trouble Restoral Reporting Code.

Bell Circuit Trouble Reporting Code ............... Section [43]

Bell Circuit Trouble Restoral Reporting Code Section [44]

5.12 Test Transmission

To ensure that the communication link with the central

station is functioning properly, the panel can be programmed

to send a test transmission signal on a regular basis.

The panel can send a Periodic Test Transmission

Reporting Code at the programmed Test Transmission

Time of Day. The Test Transmission Cycle determines the

number of days (001 to 255) between tests. If the test

transmission cycle being programmed is of a lesser value

than the previous value, the system will wait the original

period before the next test transmission is sent, and then

begin reporting with the new interval.

The panel can also send a test for the LINKS 1000 Cellular

Communicator, if being used. If the LINKS 1000 Test

Transmission Code is programmed, the panel will send a

cellular test at the same time as the land line test transmission.

The end user can generate a communicator test. If the

System Test Reporting Code is programmed, the panel

will send the signal when the System Test keypad command

is entered

(see Section 3.4 – “[(see Section 3.4 – “[

(see Section 3.4 – “[

✱✱

✱

] Commands; [] Commands; [

] Commands; [

✱✱

✱

] [6] User] [6] User

] [6] User

Functions”).Functions”).

Functions”).

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 42 43

Comentarios a estos manuales

Sin comentarios

Digital Security Controls PC1575 Especificaciones Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Security Controls PC1575