Digital Security Controls PC1575 Especificaciones descargar pdf (Pagina 15)

P R O G R A M D E S C R I P T I O N S

[10] 24 Hour Supervisory Buzzer Zone

If this zone is violated when the system is either armed or

disarmed, the panel will immediately latch the keypad

buzzer until a valid user code is entered and will immediately

communicate to the central station.

[11] 24 Hour Burglary Zone

If this zone is violated when the system is either armed or

disarmed, the panel will immediately latch the alarm output

and communicate to the central station. The alarm will

sound for the Bell Cutoff time programmed in Section [02]

(“System Times”) or until a valid user code is entered.

[12] -[20]

The following zone definitions operate similar to the 24 Hour

Burglary except for the System Event output type and the

SIA identifier:

[12] 24 Hour Heat Zone [17] 24 Hour Intrusion

[13]

Not Used

Emergency Zone

[14] 24 Hour Holdup Zone [18] 24 Hour Sprinkler Zone

[15] 24 Hour Auxiliary Zone [19] 24 Hour Water Flow Zone

[16] 24 Hour Panic Zone [20] 24 Hour Freezer Zone

[21] 24 Hour Latching Tamper

If this zone is violated, the installer must enter Installer’s

Programming before the system can be armed.

5.35.3

5.3

Zone AttributesZone Attributes

Zone Attributes

All zones, with the exception of 24 Hour and Fire,

have an exit delay. When the system is armed, the

zones may be violated during the exit delay without

causing an alarm.

Attributes for Fire Zones should not be changed

from the default settings.

Additional zone attributes can be programmed to customize

the operation of a zone for a specific application. The

following attributes are programmable for each zone:

• Audible / Silent – This attribute determines whether or not

the zone will activate the alarm output.

• Pulsed / Steady – This attribute determines whether the

alarm output will be steady or will pulse ON and OFF every

second.

• Activate Chime – This attribute determines whether or

not the zone will activate the chime feature

(see Section(see Section

(see Section

3.4 – “[3.4 – “[

3.4 – “[

✱✱

✱

] [4] Door Chime On/Off”).] [4] Door Chime On/Off”).

] [4] Door Chime On/Off”).

• Bypass Enable – This attribute determines whether or not

the zone can be manually bypassed

(see Section 3.4 –(see Section 3.4 –

(see Section 3.4 –

“[“[

“[

✱✱

✱

] [1] Bypassing and Reactivating Stay/Away Zones”).] [1] Bypassing and Reactivating Stay/Away Zones”).

] [1] Bypassing and Reactivating Stay/Away Zones”).

• Force Arm Enable – This attribute determines whether or

not the system can be armed while a zone is violated. At

the end of the exit delay, if this type of zone is violated, it

will be ignored by the panel. Once the zone is secured, it

will be monitored by the system. This zone attribute, for

example, will allow the user to arm the system with the

garage door open. Later, when the door is closed, it will be

armed along with the rest of the system.

• Downlook Activation Option (Video) – If enabled, this

attribute will activate the DLM-1/DLM-4 Downlook module.

When a given zone goes into alarm, it will activate the DLM

to take a picture of that zone.

Zones Attributes ....... Sections [21] - [26], Options [1] - [6]

5.4 Communicator – Dialing

If the Communicator Disable option is selected, the panel

will not attempt to call central station. If communication is

enabled, the panel will attempt to call central station when

an event with a valid Reporting Code occurs

(See Section(See Section

(See Section

5.7 “Communicator – Reporting Code”). 5.7 “Communicator – Reporting Code”).

5.7 “Communicator – Reporting Code”).

The Communicator Call Direction Options are used to

select which phone number the panel will dial when an

event occurs.

If the DTMF Dialing option is enabled, the panel will dial

using DTMF (touch tone). If the Switch to Pulse Dial option

is enabled, the panel will switch to pulse dialing on the fifth

attempt to call the central station. When this option is

disabled, the panel will always dial using DTMF. If DTMF

Dialing is disabled, the panel will always pulse dial.

If the Busy Tone Detection option is enabled, the panel will

hang up and redial 60 seconds after having detected a busy

tone for four seconds.

The panel will attempt to send a signal to central station

eight times before indicating a Failure to Communicate

(FTC) trouble condition. The Third Phone Number can be

used as a back up for the first number in this situation

(see (see

(see

Section 5.6 “Communicator – Phone Numbers”).Section 5.6 “Communicator – Phone Numbers”).

Section 5.6 “Communicator – Phone Numbers”).

DTMF or Pulse Dialing ................... Section [60], Option [2]

Switch to Pulse Dialing on 5th attemptSection [60], Option [3]

Communicator Enable/Disable ..... Section [60], Option [1]

Communicator Call Direction Options Section [51] to [55]

Busy Tone Detection ...................... Section [61], Option [4]

5.5 Communicator – Account Numbers

The account number is used by the central station to

distinguish between panels. There are two account numbers

programmable for the PC1575.

First Account Code (4 digits) ........................... Section [34]

Second Account Code (4 digits) ..................... Section [35]

5.6 Communicator – Phone Numbers

The panel can use three different phone numbers for

communicating with the central station. The First Phone

Number is the primary number, the Second Phone Number

is the secondary number and the Third Phone Number will

back up the First phone number if enabled.

The Third Phone Number will NOT back up the

Second Phone Number.

If the Alternate Dial option is enabled, the panel will alternate

between the first and third phone numbers when attempting

to call the central station. If the option is disabled, the panel

will only attempt to call the Third phone number after failing

to communicate with the first phone number.

In order for Alternate Dialing to work properly, the

Third Phone Number must be enabled.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 42 43

Comentarios a estos manuales

Sin comentarios

Digital Security Controls PC1575 Especificaciones Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Security Controls PC1575