Digital Security Controls PC1575 Especificaciones descargar pdf (Pagina 17)

P R O G R A M D E S C R I P T I O N S

the Fire Keys on any keypad are pressed for two seconds.

The panel will transmit a Keypad Auxiliary Alarm Reporting

Code

and

the Keypad Auxiliary Restoral Reporting Code

when the Auxiliary Keys on any keypad are pressed for two

seconds.

The panel will transmit a Keypad Panic Alarm Reporting

Code

and

the Keypad Panic Restoral Reporting Code when

the Panic Keys on any keypad are pressed for two seconds.

The panel will transmit a Duress Reporting Code any time

the Duress Code is entered at any keypad.

If PGM2 is being used for 2-wire smoke detectors or 24 hour

operation, the panel will send a PGM2 Alarm Reporting

Code if the zone goes into alarm

(see (see

(see

Appendix D – “PGMAppendix D – “PGM

Appendix D – “PGM

Output OptionsOutput Options

Output Options

”)”)

”)

. The panel will transmit the PGM2 Restoral

Reporting Code when the zone is restored.

The above is only applicable to pulse format.

Priority Alarm and Restoral Reporting Codes Section [40]

5.7.7 Maintenance

The panel will transmit a Battery Trouble Alarm Reporting

Code when the backup battery charge drops below 11.5

DC. The Battery Trouble Restoral Reporting Code will not

be transmitted until the battery has been charged to over

12.5 VDC.

To prevent the panel from transmitting an AC Failure Trouble

Alarm Reporting Code during short power outages, the panel

will not send the signal unless AC power is lost for the amount

of minutes programmed for the AC Failure Communication

Delay. The AC Failure Trouble Restoral Reporting Code will

be transmitted as soon as AC power is restored.

A Bell Circuit Trouble Alarm Reporting Code will be

transmitted immediately when an open condition is measured

for the Bell Output of the main panel. The Bell Circuit

Trouble Restoral Reporting Code will be transmitted as

soon as the problem is corrected.

A Fire Trouble Alarm Reporting Code will be immediately

transmitted when an open condition is measured on any Fire

type zone

(see Section 5.2 – “Zone Definitions”). (see Section 5.2 – “Zone Definitions”).

(see Section 5.2 – “Zone Definitions”).

The Fire

Trouble Restoral Reporting Code will be transmitted as

soon as the problem is corrected.

The Auxiliary Power Supply Trouble Alarm Reporting

Code will be transmitted if the AUX output is shorted out. The

AUX output of the control incorporates a fuseless design.

When excessive current is drawn, the panel will automatically

shut off the output. The panel will constantly check the AUX

output; when the excessive current draw is removed, the

panel will reset the output and transmit an Auxiliary Power

Supply Trouble Restoral Reporting Code.

A TLM Trouble Reporting Code can only be transmitted if a

LINKS 1000 Cellular Communicator is being used

(see(see

(see

Section 5.23 “LINKS 1000 Cellular Communicator”)Section 5.23 “LINKS 1000 Cellular Communicator”)

Section 5.23 “LINKS 1000 Cellular Communicator”)

. The

panel will only transmit the signal after the time programmed

for the TLM Trouble Delay. The TLM Restoral Reporting

Code will be transmitted within 10 seconds of the problem

being corrected.

A General System Supervisory Trouble Reporting Code

will be transmitted if any module goes missing from the

KEYBUS. The panel will send a General System Supervisory

Restoral Reporting Code when the problem is corrected.

Maintenance Alarm Reporting Codes ............. Section [43]

Maintenance Restoral Reporting Codes ........ Section [44]

AC Failure Communication Delay ................... Section [62]

5.7.8 Test Transmissions

The panel can be programmed to transmit a Periodic Test

Transmission Reporting Code

(see Section 5.13 – “Test(see Section 5.13 – “Test

(see Section 5.13 – “Test

Transmissions”)Transmissions”)

Transmissions”)

, a System Test Reporting Code

(see(see

(see

Section 3.4 – “[Section 3.4 – “[

Section 3.4 – “[

✱✱

✱

] [6] User Functions”] [6] User Functions”

] [6] User Functions”

) or a LINKS 1000

Test Transmission Reporting Code

(see Section 5.23 –(see Section 5.23 –

(see Section 5.23 –

“LINKS 1000 Cellular Communicator”).“LINKS 1000 Cellular Communicator”).

“LINKS 1000 Cellular Communicator”).

Test Transmission Reporting Codes............... Section [46]

5.7.9 Miscellaneous

If the panel fails to transmit information to the central station,

it will display a Failure To Communicate (FTC) trouble

condition. The panel will transmit a Phone Number 1 Failure

to Communicate Reporting Code or a Phone Number 2

Failure to Communicate Reporting Code the next time it

calls the central station. The panel will transmit the old

events, followed by the FTC message, followed by the new

events. This will allow central station to determine which

events are old or new.

If the Event Buffer is uploaded or printed on-site on a regular

basis, an Event Buffer 75% Full Reporting Code can be

transmitted to warn that the buffer is almost full. This code is

good for use with the PC5400 Printer Module.

The General Zone Fault Alarm Reporting Code is sent

whenever a DEOL hardwired zone is shorted out. The

faulted zone will also be displayed in the Trouble section.

The General Zone Fault Restoral Reporting Code will be

sent when the problem zone is repaired.

The Delinquency Reporting Code is sent whenever the

panel is not armed within the number of days programmed

for the Delinquency Transmission Delay.

Miscellaneous Maintenance Reporting CodesSection [45]

Delinquency Transmission Delay .................... Section [62]

If the Delinquency Tx Delay is set for 1 day, there

must be 24 hours of no arming or disarming before

the Delinquency Code will be sent.

After a Delinquency Code has been transmitted, it

will not send again until the system has been armed

and disarmed.

5.8 Communicator – Reporting Formats

Each central station communication phone number can be

programmed to report using any one of the 4 formats

available. A 20 BPS pulse format is supported in addition to

Contact ID, SIA and a Pager format.

Communicator Format Options ....................... Section [50]

Communicator Call Directions ............ Section [51] to [55]

The following is a description of each reporting format:

5.8.1 Pulse Formats

Depending on which pulse format is selected, the panel will

communicate using the following specifications:

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 42 43

Comentarios a estos manuales

Sin comentarios

Digital Security Controls PC1575 Especificaciones Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Security Controls PC1575